Fault 1
When the first color combination is pressed, sometimes there is no pressure, and the pressure is manually closed, and the phenomenon is the same. Check the closed piezoelectric magnet coil, the resistance value is normal, but sometimes there is no when 24V power supply, X10 of WP12 has a green indicator light and it does not light, check the output module in the electric cabinet has an output indication every time, but there is no voltage output, It is suspected that the micro relay in the output module is damaged. After the output modules 50A4 and 50A5 are exchanged, the closing pressure is normal. After removing the 50A4 board and replacing the miniature relay, the machine works normally.
Fault 2
The first group of pattern-making motors does not work. Both the circumferential and axial patterns cannot be patterned, but there is a pattern-making display at the Colortronic window. Check Registermodule129, the 24V power supply voltage is normal, and the Monitoring indicator light will indicate when printing, UR +-. SR +-are adjustable, but there is no voltage output at the P1 socket. Measure the potentiometer (1kΩ) at the P8 plug is normal, the output of the pattern motor is 4A, with protection, it is suspected that the positioning controller is broken. After changing the positioning controller, the pattern-making motor works normally.
Fault 3
There is an electric bell but there is no jogging and no operation. Check the safety circuit is normal, the input signal is normal, but there is no brake to absorb the closing sound, 99K4 does not absorb, 24Y1 has no electricity. Check the control output circuit board 70A5 (MCIF23 board number is 495052), and found that its X3 / 7 (maindrivebrake), X3 / 8 (maindriverampon) output indicator does not light, indicating that there is no signal output, so remove 70A5. It is suspected that the miniature relay is bad, but check the coil of the relay, the resistance value is normal, the normally open contact is normal, and then check the connection between the output point and the relay. It is found that the two small capacitor feet C67 and C68 have red marks. Both are bad (model 103K100V). After replacing the capacitor with the same specification, the fault is eliminated and the machine operates normally.
Fault 4
The power supply of the electric cabinet sometimes buzzes when it is closed, sometimes there is no operation, sometimes there is no jogging, sometimes there is no response when pressing the forward and reverse jogging; sometimes the water roller motor of any unit is turned on, and the machine will automatically Turn it up, it can run normally for about 1 hour. The failure is irregular, irregular and chaotic. At the beginning, there is really no way to start, I do not know how to find the fault. Because 70A4. 70A5, 80A4, 80A5 are the main control board (MCIF23), and the same model is interchangeable, so the method of exchanging the control circuit boards in the electric cabinet is adopted, but the failure remains. When the circuit boards 50A4 and 50A5 are exchanged (MCIF22 board number is 495001), when the 50A5 is changed to the position of 50A4, the machine can run and the jogging is normal, but the shield of each unit cannot be lifted. Power off. When the circuit board is changed back to the original position, the machine has no electric bell and jog function, indicating that the 50A4 is faulty. Because there is no spare board, check the miniature relays on the board one by one. Resistance, integrated block, found that the 18 and 19 pins of the integrated circuit IC2 (UDN2987A) are not in good contact. After cleaning with alcohol, reinstall it on the machine. The machine can jog and the safety circuit is normal after lifting the hood.
Originally thought that the fault has been resolved, but after a few hours after starting up, the machine automatically runs into trouble when the water roll is turned on. Measure the voltage of 50A4's X7 / 3 pin (inchreverse delivery side) to ground. There is a voltage of about 8V. When a group of water roller motors are turned on, the voltage rises by 2V, sometimes 1V. Cut the X7 / 3 line, the machine works normally, the above fault disappears, and lose. The reverse point at the delivery point is normal, but there is no reverse point for each unit. Check the anti-point button switches of each unit one by one, check the DWP12 circuit board of each unit, and find that there is a trace of corrosion of the old fountain solution at the X1 socket of the DWP12 board of the second group. Measure 20 feet (machineinchreserve) and 13 feet ( damprollerautomatic) has a resistance value of 450Ω. Observation and analysis from the point of failure, the board once leaked water due to the water bucket, and there was water droplets on the X1. After a long time, the back of the socket produced rust marks, which formed a phenomenon of continuous electricity. Clean the back of the socket with a cleaning agent, alcohol, and clean the back of the socket with a needle before trying the machine. Everything is normal and the above faults are eliminated.
Cooler Bags also called ice bags, insulation bags, which has the effects of warming in summer and cooling in winter. The inner layer of the product is pearl cotton coated with aluminum foil reflective heat insulation layer to provide good thermal insulation effect. It's easy to carry, suitable for driving, holidays, family picnics.
With the increase of market demand, the appearance of new model insulation bags brings great convenience to the public.
Olinb Bags are a manufacturer who specialize in making custom bags, attaching a label for you.
To avoid any bad feedback about quality from buyers, it is guaranteed that all of our bags will be well made and 100% checked before delivery. If any issue on quality, free replacement will be sent to you.
Olinb Bags' products will give you an edge over your competitors.
Cooler Bags
Cooler Bags,Aluminium Foil Cooler Bag,Insulated Cooler Bag,Cooler Lunch Bag
Shenzhen Olinb Bags Co., Ltd. , https://www.szolinbbags.com