The wooden door will inevitably fade after a long time, and the wooden door is a fixed household product, so many do not know how to color the wooden door. The extreme wooden door specifically summed up the procedure for how to color the wooden door.
Wooden door coloring steps:
1. Clean the door only with a clean soft cloth and take organic solvent to thoroughly clean the entire surface of the door.
2. Prepare the work to protect the glass, hardware and sealing strip on the door before painting. The sealing strip can be removed from the door frame first, and after the color drying is completed, the sealing strip is installed.
3. Stir the dye gently and stir well. If the stirring is insufficient, the dye will not dry easily.
4. Coloring experiment Prepare a sample of the door panel for dyeing. The results of the dyeing experiment can well reflect the dyeing effect of the door. Using the prepared sample, follow the steps below to perform the dyeing experiment: Prepare a soft cloth for dyeing, and after staining, make the surface of the door sample. Apply in a circular or diagonal texture so that the dye can better reflect the texture of the wood. If you want to dye a little lighter, after a few minutes, you can erase the excess color. If you want to dye deeper, repeat the above staining step. If you want to re-stain, you can easily remove the stain with mineral solvents. Put the stained sample aside and you will continue to use it in step 8.
5. When dyeing and dyeing, the same area of ​​the door panel should be completed at the same time. Coloring is described in steps 5a, 5b, and a better dyeing effect can be achieved. The distinguishing area of ​​the door panel dyeing: 1. door frame, door edge, door pillar, decorative strip, etc.; 2. decorative panel inside the door panel; 3. flat area inside the door panel; 4. glass frame; 5. flat area outside the door; The door panels are not primed and need to be cleaned with wood care or mineral solvents before coloring. 5a. Inside the deep groove of the door panel, use the tip of the foam brush to paint. 5b. The texture part is painted with a soft cloth or an oblique texture.
6. Uniform color A. Use a soft cloth for coloring to apply in the direction of the grain to remove the arc marks during coloring. B. Dry for 10-15 minutes. C. Using a clean soft cloth, follow the texture of the wood, and apply unevenly and darkly to the desired area. If a darker dyeing effect is desired, the dyeing operation can be performed again after drying for 2-4 hours after the last dyeing.
7. Mix A. Use a 3 inch natural soft brush to evenly apply the colored parts, especially in the deeper grooves and at the corners of the decorative panels.
Do not use a 3-inch natural soft brush to remove excess stains during coloring. Because the stain is easy to stick to the soft brush. If the soft brush has been stained with a stain, it can be removed with a soft cloth dipped in mineral solvent.
8. Drying experiment A. Confirm the dryness of the dye with the previous dyed sample to determine whether the paint can be applied. B. Dyeing on the remaining samples. C. The stained sample was dried for at least 6 hours. D. Remove a clean cloth tape from the colored sample and rub the cloth strip on the door panel with a hard object. If the strip is not stained, it is proven to be completely dry. Otherwise, the experiment is performed every hour and it has been confirmed whether the dye is completely dry. Dark and multi-layer dyeing may require more drying time.
9. Stir the varnish while stirring, do not shake. It is easy to generate bubbles and affect the painting.
10, varnish A. Dip the top of the 2 inch synthetic brush, a thin layer of varnish. Completed in the same area of ​​the door panel. It can also be applied on two experimental samples. The brush is then cleaned with detergent. B. Wait 2-3 hours, the first layer of varnish is dry. C. Apply the second layer. At this point the surface of the door may look very moist, but it is not cloudy. It is also possible to apply on the test sample and clean the brush. The first time the lacquer is used, it will be milky and will become clear and transparent after drying. Do not reuse the brush and clean it after each use. Otherwise, it is easy to produce spherical particles and various flaws on the surface of the lacquer. Once this happens, wait for 30 minutes. After the varnish is dry, wipe it gently with a clean soft cloth. Apply a thin layer of new lacquer to polish it.
Document.body.oncopy = function () { setTimeout( function () { var text = clipboardData.getData("text"); if (text) { text = text + " This article comes from China Wooden Door Network, China's well-known wooden door industry portal Website! (http://) Detailed reference: "+location.href; clipboardData.setData("text", text); } }, 100) }Dip Paint Caper Hanger,Gold Coat Hanger,Custom Gold Cloth Hanger,Hanger Caped Hanger
SHAOXING DINGLI METAL CLOTHESHORSE CO., LTD , https://www.dingliclothrack.com